Harness Spreaderbar_Hero Banner

Spectre Bar tutorials

Find step-by-step instructions for replacing the hook, installing a mini rope or webbing slider, and adjusting your ION Spectre Bar. Select your model below to find the right tutorial.

Table of Content
Spectre Bar 2

Spectre Bar

How to replace the hook: Spectre Bar 2

What You'll Need:

  • Compatible replacement hook

  • Torx T20 screwdriver

  • Torque screwdriver (recommended)

Step-by-Step Instructions

Remove the Spreader Bar: Open the two side levers and detach the Spectre Bar 2 from your harness.

Remove the Five Screws: Use a Torx T20 screwdriver to remove the five screws on the back. Keep the screws and washers for reassembly.

Remove the Old Hook: Carefully disassemble the spreader bar and remove the damaged or worn hook.

Install the New Hook: Place the replacement hook into the center slot of the Spectre Bar 2.

Reattach the Side Wings and EVA Pad: Clip the two side wings into place. Position the EVA pad with the two recesses facing upwards, towards the hook opening.

Insert the Center Screw: Position the center washer and insert the center screw. Check that the screw still has blue threadlocker to prevent loosening.

Insert the Remaining Screws: Insert the remaining screws and washers. Tighten them lightly at first to keep all components aligned.

Tighten All Screws: Use a torque screwdriver to tighten all five screws to the recommended 2.5 Nm.

Reattach and Check the Spreader Bar: Reattach the Spectre Bar 2 to your harness. Make sure both side levers are securely closed and all components are properly installed.

Important: Only use compatible ION replacement parts. Do not use your harness if any components are damaged, loose or incorrectly installed.

Thumbnail for Repair and Care Video on how to change a hook on a harness.

INSTALLING THE MINIROPE: SPECTRE BAR 2

Step 1: Remove all five screws from the inside of your Spectre Bar 2 using a TX20 Torx driver.

Step 2: Carefully remove the pad, flaps, and hook.

Step 3: Remove the front cover by pushing the two small plastic tabs on each side of the bar.

Step 4: Replace the original cover with the enclosed replacement part.

Step 5: Make a figure-eight knot on one side oft he mini rope.

Step 6: Run the mini rope through one of the holes on the Spectre Bar 2.

Step 7: Run the mini rope back through the other hole.

Step 8: Secure it with another figure-eight knot on the inside.

Step 9: Thread the webbing slider through the Spectre Bar 2.

Step 10: If using a stanndard chicken loop, add the stainless steel ring. If using the Duotone Rope Kit, the ring is not needed.

Step 11: Place the rope cover over the webbing slider.

Step 12: Insert the two screws next to the center through the rope cover and rope.

Step 13: Tighten the screws holding the hook to 2.5Nm. Tip: you can adjust the rope length.

Step 14: Long rope: Use both inner holes. Medium rope: Use one inner and one outer hole. Short rope: Use both outer holes.

Step 15: Secure everything tightly.

Step 16: Reassemble the flaps and pad, including the washers. Fasten with the remaining three screws.

Thumbnail for how to video on how to install the minirope for a kite harness.

Installing the Slider: Spectre Bar 2

Step 1: Remove all five screws from the inside of your Spectre Bar 2 using a TX20 Torx driver.

Step 2: Carefully remove the pad, flaps, and hook.

Step 3: Thread the webbing slider through the Spectre Bar 2.

Step 4: If using a standard chicken loop, add the stainless steel ring. If using the Duotone Rope Kit, the ring is not needed.

Step 5: Place the rope cover over the webbing slider.

Step 6: Insert the two screws next to the center through the rope cover and rope.

Step 7: Tighten the screws holding the hook to 2.5Nm.

Step 8: Tip: You can adjust the rope length. Long rope: Use both inner holes. Medium rope: Use one inner and one outer hole. Short rope: Use both outer holes.

Step 9: Secure everything tightly.

Step 10: Reassemble the flaps and pad, including the washers. Fasten with the remaining three screws.

Thumbnail for tutorial on how to install the slider on a kite harness.

How to change the hook on the Spectre Bar

Step 1: Remove the three middle screws that secure the hook of the Spectre bar using a TX20 Torx

Step 2: Remove the hook from the Spectre bar

Step 3: Put the place holder back into it's original position

Step 4: Add new hook to the Spectre bar

Step 5: Put the three screws back into their original position. Make sure the longest 20mm screw is in the center

Thumbnail for How-to video on how to change the hook on a kite harness.

How to install the webbing slider on the Spectre Bar

Step 1: Remove all five screws from the inside of your Spectre Bar using a TX20 Torx

Step 2: Carefully, remove the pad, flaps & hook

Step 3: Assemble the hook place holder

Step 4: Run the webbing slider through the Spectre Bar

Step 5: Cut the webbing slider to your preferred length

Step 6: If you are using a standard chicken loop, add the stainless steel ring. If you are using the Duotone Rope Kit you don't need the ring

Step 7: Place the aluminium bar on top of the webbing slider

Step 8: Put the screws through the aluminium bar & through the webbing slider. Secure tightly.

Step 9: Add the hook place holder, reassemble the flaps & secure everything with the screws. Make sure to put the longest screw in the center.

Thumbnail for How-to video on how to install webbing slider on a kite harness.

How to install the webbing slider + mini rope on the Spectre Bar

Step 1: Remove all five screws from the inside of your Spectre Bar using a TX20 Torx

Step 2: Carefully, remove the pad, flaps & hook

Step 3: Remove the front cover by pushing the two small plastic tabs on each side of the bar

Step 4: Replace the original cover the the enclosed replacement part

Step 5: Make a figure-eight knot on one side of the mini rope

Step 6: Run the mini rope through one side of the aluminium bar

Step 7: Now run it through one of the holes of the Spectre Bar

Step 8: Run the mini rope back through the other hole in the Spectre Bar. Secure it with another figure-eight knot on the inside

Step 9: Install the webbing slider according the instruction (see above)

Thumbnail for How-to video on how-to you video on how to install the webbing slider and mini rope for a kite harness.

How to remove the flaps on the Spectre Bar

Step 1: Using a Torx TX20 remove the two outer screws on the inside of your Spectre Bar

Step 2: Remove the flaps by pulling them downwards

Step 3: Put both screws back in and secure them tightly

Thumbnail for How-to video on how to remove flaps on kite harness bar.

More ION guides & services